There is an increasing need for research chemists and biochemists to have a basic familiarity with computer programming. Adding programming content to already crowded STEM undergraduate curricula, however, can be challenging. When programming content is introduced within the chemistry curriculum, it is most often incorporated into upper division…

This paper presents a set of laboratory classes to be taught as a part of a 1 year calculus-based physics class. It is composed of 7 modules designed to bring together experiments and computer simulations. Each module uses both simulations and experiments to address a phenomenon under study, and lasts for 3 weeks (21 weeks total for the whole…

In this article, we describe a basic practical laboratory designed for fifth-year undergraduate students of Microbiology as part of the Epidemiology course. This practice provides the students with the tools for molecular epidemiological analysis of pathogenic microorganisms using a rapid and simple PCR technique. The aim of this work was to assay…

A hands-on educational module was created to illustrate the scope of chemical engineering. Students are taught fundamental concepts that they integrate in a laboratory experience designing and fabricating a 'plant-on-a-chip' microfluidic device capable of continuous processing of reactive flows. Students gain insight into chemical engineering…

The present study describes the design of a simple teaching module for each student to fabricate a dye-sensitized solar cell (DSSC) that could power a small fan motor. The significance of this laboratory exercise is to stimulate students' motivation by visualizing the light being converted into electricity, which is then switched over to kinetic…

Implementing enzyme-linked immunosorbent assays (ELISA) in microchannels offers several advantages over its traditional microtiter plate-based format, including a reduced sample volume requirement, shorter incubation period, and greater sensitivity. Moreover, microfluidic ELISA platforms are inexpensive to fabricate and allow integration of…

A novel studio-based lab module that incorporates student-centered activities was designed and implemented to introduce second-year undergraduate students to the first-semester organic chemistry laboratory. The "First Day" studio module incorporates learning objectives for the course, lab safety, and keeping a professional lab notebook.

A 3D model visualization and basic molecular modeling laboratory suitable for first-year undergraduates studying introductory medicinal chemistry is presented. The 2 h practical is embedded within a series of lectures on drug design, target-drug interactions, enzymes, receptors, nucleic acids, and basic pharmacokinetics. Serving as a teaching aid…

A lithography lab course has been developed that is applicable to students from the middle-school level up to college students. It can also be inserted into electronics technology or similar courses in two- and four-year colleges, or used to demonstrate applications of polymers in chemistry classes. Some of these techniques would enable research…

This paper presents low-cost experiments for a control systems laboratory module that is worth one and a third credits. The experiments are organized around the microcontroller-based control of a permanent magnet dc motor. The experimental setups were built in-house. Except for the operating system, the software used is primarily freeware or free…

Engaging undergraduate students in designing and executing original research should not only be accompanied by technique training but also intentional instruction in the critical analysis and writing of scientific literature. The course described here takes a rigorous approach to scientific reading and writing using primary literature as the model…

The University of Waterloo, Waterloo, ON, Canada, is home to North America's first undergraduate program in nanotechnology. As part of the Nanotechnology Engineering degree program, a scanning probe microscopy (SPM)-based laboratory has been developed for students in their fourth year. The one-term laboratory course "Nanoprobing and…

Personalized medicine refers to medical care that involves genetically screening patients for their likelihood to develop various disorders. Commercial genome screening only involves identifying a consumer's genotype for a few single nucleotide polymorphisms. A phenotype (such as an illness) is greatly influenced by three factors: genes, gene…

This paper describes a one-credit laboratory course for freshmen majoring in electrical and computer engineering (ECE). The course is motivational in nature and exposes the students to a wide range of areas of electrical and computer engineering. The authors believe it is important to give freshmen a broad perspective of what ECE is all about, and…

A scanning tunneling microscope (STM) project designed as a module for the undergraduate physical chemistry laboratory is described. The effects of van der Waals interactions on the condensed-phase structure are examined by the analysis of the pattern of the monolayer structures.