The article introduces a low-cost Arduino sensor into the Young's modulus determination laboratory for physics university students. A stainless steel ruler is used as a cantilever beam. Its free end attached a mass is slightly bent and released to make it oscillate as a simple harmonic motion. The Arduino sensor detects the moving mass's frequency…

We developed a single crystal X-ray crystallography experiment based on the crystal structure of sucrose (table sugar), and a more challenging experiment using Epsom salt. Both crystals are readily available in X-ray quality crystalline form. In these experiments, students mounted a crystal on a MiTeGen loop and analyzed it using a Rigaku XtaLAB…

Encouraging student engagement is a key aim in any educational setting, and allowing students the freedom to pursue their own methods of solving problems through independent experimentation has been shown to markedly improve this. In many contexts, however, allowing students this flexibility in their learning is hampered by constraints of the…

In science class, students learn by making and living information, enabling them to make sense of knowledge effectively and permanently and to associate it with daily life. Applied science courses make learning more qualified. While science teaching is carried out in application areas such as laboratories, virtual laboratories are used with the…

The experiment in charging and discharging of a capacitor through a resistor is fundamentally important for studying electronics. We have developed an alternative procedure to measure the voltage drops across capacitors as a function of time. The simple apparatus controlled by an Arduino Uno microcontroller board and LabVIEW™ interface was set up.…

Here, students determine the total protein content in whey protein samples using the Lowry assay. Quantitative analysis was carried out using absorbance measured at 750 nm (standard method) and 96-well-plate digital images obtained using smartphones (proposed method). The proposed method was carried out using two smartphones (1 and 2). Smartphone…

A virtual microscope resource was created when face-to-face labs were halted due to the COVID-19 pandemic in March 2020 to replicate the learning goals of an introductory petrology course on microscopy. This virtual microscope resource utilized images and videos of thin sections, as well as 3D rock models to allow students to complete labs online.…

Basic Human Anatomy at Indiana University is a large undergraduate anatomy class with nearly five hundred students in twelve lab sections. In the fall of 2018, we added the Virtual Human Dissector software on an interactive Sectra table to our lab to help students fill the gap between idealized anatomical models and fully prosected cadavers. We…

At Kansas City University, anatomy laboratories were delivered via remote (REM) or on-campus (OC) formats due to COVID-19, creating an opportunity to evaluate student perceptions of differences in laboratory delivery format. A six-item survey of Likert scale and open-ended questions explored the utility of anatomy software, prelab instruction…

The COVID-19 pandemic has forced a shift in thinking regarding the safe delivery of wet laboratory courses. While we were fortunate to have the capacity to continue delivering wet laboratory experiments with physical distancing and other measures in place, modifications to the mechanisms of delivery within courses were necessary to minimize risk…

This study has proposed a simple method to show the convective heat transfer. The object in this study is an air conditioner (AC) as a simple case of convection. In addition, AC is also easy to find in the class because most classrooms in Indonesia installed AC. Usually, a visualization needs special software (i.e. MatLab or others) and good…

To help educators deliver their physiology laboratory courses remotely, we developed an inexpensive, customizable hardware kit along with freely available teaching resources. We based the course design on four principles that should allow students to conduct insightful experiments on different physiological systems. First, the experimental setup…

Science, technology, engineering, and mathematics (STEM) students are typically taught content delivered didactically and closely aligned with the laboratory demonstration of concepts, which facilitates the development of experimental skills. Because of the volume of content delivered across multiple courses, student cognitive abilities can be…

For conducting laboratory experiments on Fresnel diffraction, the use of a simple point light source from an LED and the application of a modern smartphone for photographing the diffraction patterns are proposed. The developed devices allow the experiments to be carried out under normal laboratory lighting.

The COVID-19 pandemic and its related restrictions forced the reorganization of learning methodology and gave a central role to remote learning. Laboratory experiments are the most affected activity, and several alternatives were described. This work proposes to create calculation tools by simply programming in Visual Basic of Excel to emulate the…