The article introduces a low-cost Arduino sensor into the Young's modulus determination laboratory for physics university students. A stainless steel ruler is used as a cantilever beam. Its free end attached a mass is slightly bent and released to make it oscillate as a simple harmonic motion. The Arduino sensor detects the moving mass's frequency…

For conducting laboratory experiments on Fresnel diffraction, the use of a simple point light source from an LED and the application of a modern smartphone for photographing the diffraction patterns are proposed. The developed devices allow the experiments to be carried out under normal laboratory lighting.

This paper describes the development of a light polarization experimental apparatus for a remote laboratory. The apparatus had been developed by controlling the analyzer rotation using a stepper motor controlled via the Arduino. Device control and data acquisition applications were developed with LabVIEW which provides remote control panel…

This study has proposed a simple method to show the convective heat transfer. The object in this study is an air conditioner (AC) as a simple case of convection. In addition, AC is also easy to find in the class because most classrooms in Indonesia installed AC. Usually, a visualization needs special software (i.e. MatLab or others) and good…

Electroscopes have been widely used in physics education for several reasons, such as their simplicity, sensitivity and visual appeal, showing macroscopic phenomena related to the microscopic world. Although they are capable of highly accurate measurements, the procedures involved in these measurements encounter some obstacles when performed with…

Teaching materials used in distance education are generally obtained from the internet as ready-made by teachers. Materials such as simulation, animation and presentation are usually limited to the frame drawn by the creator and do not allow changes outside this limit. In addition, many of these types of materials do not have a feedback mechanism.…

In this work we construct a timer system consisting of both hardware and software to be used in introductory-level laboratory physics courses. The Parallax P8X32A propeller based-microcontroller hardware consist of a board that registers the times of events triggered when IR photogates are blocked and unblocked. The software allows the user to…

A Science, Technology, Engineering and Mathematics (STEM) tool is proposed in this manuscript; which consists of an interactive, simple and low-cost computer based simulation and game, with the aim of easing the teaching/learning process regarding the physics concept of projectile motion. The novelty of this proposal relies on the use of a…

This study demonstrated that the constant average speed of a dynamic car could be measured and calculated using the smartphone magnetometer. The apparatus setup was built using a dynamic car, a linear track up to 1.50 m, a bunch of magnets, and a smartphone magnetometer application. The smartphone magnetometer application, 'Physics Toolbox Suite',…

In conventional e/m experiments performed in undergraduate laboratories, generally a simple mechanical ruler is used to measure the radius of the circular trajectory of the electrons. But, the measurement error in this technique is mostly big and varies from one student to another. As an alternative to a mechanical ruler, we proposed a more…

The introduction of electric circuit simulation software for undergraduate students in a general physics course is proposed in order to contribute to the constructive learning of electric circuit theory. This work focuses on the lab exercises based on dc, transient and ac analysis in electric circuits found in introductory physics courses, and…

This study used a smartphone's digital compass to observe the rolling motion of a hollow cylinder on an inclined plane. The smartphone (an iPhone 4s) was attached to the end of one side of a hollow cylinder to record the experimental data using the SensorLog application. In the experiment, the change of angular position was measured by the…

This paper shows how very simple circuitry attached to an Arduino microcontroller with MakerPlot software can be used for the display of electrical characteristic curves of three commonly available devices: an ohmic resistor, an LED, and a tungsten-filament bulb.

This paper demonstrates some simple applications of how temperature logging systems may be used to monitor simple heat experiments, and how the data obtained can be analysed to get some additional insight into the physical processes. [For "DIY Soundcard Based Temperature Logging System. Part I: Design," see EJ1114124.]

We use apparatus based on two Geiger-Müller tubes, a simple electronic circuit and a Raspberry Pi computer to illustrate relativistic time dilation affecting cosmic-ray muons travelling through the atmosphere to the Earth's surface. The experiment we describe lends itself to both classroom demonstration to accompany the topic of special relativity…