A single-slit diffraction experiment in an introductory physics laboratory is generally comprised of a rectangular slit and a laser source. The laser beam is sent to the slit producing the well-known diffraction pattern on the screen. This paper proposes a simple modification of the single-slit diffraction experiment to increase student attention…

Online video experiments are a promising educational technology tool for science laboratory classes. In order to find optimal instructional designs and scenarios for using online video experiments, we need to study learners' experiences. This work describes implementation of an online interactive video experiment at the undergraduate introductory…

Undergraduate physics laboratory exercises are very important in shaping students' attitude to science, especially for future teachers. Recently, it is necessary to look for ways to easily create large quantities of experimental sets, not only for institutional use, but also for sets that can be produced in large quantities and distributed for use…

During the COVID-19 pandemic and subsequent lockdown, both schools and universities faced significant challenges in moving teaching from an in-situ setting to a remote one, this included laboratory experiments. This paper presents an experiment developed to use a phone's in built pressure sensor, common to most smart phones. By using this sensor…

The article introduces a low-cost Arduino sensor into the Young's modulus determination laboratory for physics university students. A stainless steel ruler is used as a cantilever beam. Its free end attached a mass is slightly bent and released to make it oscillate as a simple harmonic motion. The Arduino sensor detects the moving mass's frequency…

Light emitting diodes have been used to determine Planck's constant in introductory physics laboratories. One common method relies on the energy of the light emitted by the LED and its relation to the energy gap in the solid of which the diode is composed. However, there could be a problem with the data that are collected for this experiment. For…

In this article, we examine the rotation angle dependence of a hand-made fan-type variable capacitor for use in physics experiments in university classes. We made two circular bakelite plates, and the two terminal plates of the capacitor were 90° fan-type copper disks. The capacitance varied linearly with the rotation angle. The standard deviation…

In this study, it is aimed to develop practical teaching activities that can be used in optics teaching. For this purpose, a virtual laboratory environment was created in RayLab which is an application for design and simulation of optics on the iPad/iPhone. In this context, the dispersion of white light in the prism, the relationship between the…

This article describes a simple setup of electrospinning using widely available resources. The Arduino board, an electronic platform that is commonly accessible was adapted for a controller. Specifically, recycled parts consisting of plastic gears and a lipstick case were incorporated for the construction of a syringe pump. A cheap DC-DC converter…

Induced seismicity has received a lot of attention in recent years. This new natural phenomenon appeared as a result of active human influence on nature. The phenomenon has been detected in places of natural gas and oil recovery, and geological storage of CO[subscript 2]. One of the main reasons for the observed seismic activity is associated with…

We designed and tested a 3D motion tracking system which displays acquired and derived data using augmented reality. This setup, based on a virtual reality headset and its controllers, is a relatively low-cost, high-precision, six degrees of freedom, high-speed, multiple-objects tracking device. This apparatus proves to be a very high-quality…

We have designed an Arduino-based experiment to check the linear relationship between charge and voltage drop in a capacitor. The electric charge stored in a capacitor is determined by the numerical integration over time of the electric current during the charging or discharging processes through a resistor. Instead of using scientific software to…

For conducting laboratory experiments on Fresnel diffraction, the use of a simple point light source from an LED and the application of a modern smartphone for photographing the diffraction patterns are proposed. The developed devices allow the experiments to be carried out under normal laboratory lighting.

When injecting dye into a vortex, one finds that the dye remains captured around the vortex core over minutes, despite the fact that the vortex (and the dyed region) is strongly time-dependent. According to a recent theory, three-dimensional time-dependent vortices should be defined as rotating, material-holding regions of the fluid. Vortices…

The pendulum was an important scientific instrument in the 17th century. It became a typical textbook problem in the 18th century. After the introduction of vectors in physics in the 1890s, the pendulum problem started to be progressively solved in the manner we know nowadays from introductory mechanics courses. Starting from "F = ma"…