This course syllabus is for five 18-week courses in the Metal Fabrication Program at Northeast Wisconsin Technical College (NWTC): (1) metal fabrication I; (2) blueprint reading and sketching; (3) applied layout tech I; (4) metal fabrication II; and (5) applied layout tech II. Each syllabus contains some or all of the following: (1) course…

This report investigates the feasibility of including computer aided design (CAD) materials in engineering courses. Section 1 briefly discusses the inevitability of CAD being adopted widely by British industry and the consequent need for its inclusion in engineering syllabi at all levels. A short description of what is meant by CAD follows in…

Computer-aided drawing can bring new technology into the drafting classroom. One approach to computer-aided drafting (CAD) involves use of a personal computer and purchased software. Existing school computers could be shared to reduce costs. Following this narrative introduction, a suggested curriculum for the teaching of CAD is presented in…

Originally created in the late 1960s, DACUM (Developing a Curriculum) is a method for conducting an occupational analysis that identifies the tasks that must be performed by persons employed in a specific job or occupational area. As a result of the occupational analysis, a profile chart is developed that identifies the duties and tasks associated…

This guide is intended to assist teachers in using computer-aided design (CAD) workstations and artificial intelligence software to teach basic drafting skills. The guide outlines a 7-unit shell program that may also be used as a generic authoring system capable of supporting computer-based training (CBT) in other subject areas. The first section…

Designed to assist the classroom teacher in keeping abreast of the most recent instructional and technical developments in the field of drafting, this guide includes information that has been identified and validated by incumbent workers, trade unions, professional organizations, and teachers. It is also designed to be of use to curriculum…

This document contains the new and verified task lists for 10 occupations: shipping and receiving clerk; general office clerk; billing, cost, and rate clerk; order clerk; accounting clerk; typist/word processor; drafter; cook; automobile mechanic; and carpenter. The DACUM (Developing a Curriculum) process task analysis and survey verification and…

A two-part articulation instructional objective guide for drafting (graphic communications) is provided. Part I contains summary information on seven blocks (courses) of instruction. They are as follow: introduction; basic technical drafting; problem solving in graphics; reproduction processes; freehand drawing and sketching; graphics composition;…

Intended for use in competency-based and criterion-referenced vocational programs, this articulated, performance-based instruction objectives guide for Drafting I is designed for reference use in the articulation of drafting programs at the secondary and postsecondary levels. It consists of a description of the development of the guide, 14…

Individualized, competency-based curriculum materials were developed for a course on Principles of Technology, Units 1-6. New and updated curriculum materials in Drafting and Electronics and the Principles of Technology units were pilot tested in area vocational center settings in Illinois. A computer maintenance program was also developed but not…

Developed through synthesis and review of existing task analysis literature, this guide lists tasks expected to be performed by workers in nine trade and industrial occupations and presents information for incorporating these tasks into articulated secondary and postsecondary competency based vocational education programs. Task listings are…

Abstracts of the following 52 papers are included in this document: "Development of a Computer-Automated Mechanical Testing System" (Aman); "Bringing Industry High-Tech into the School Curriculum" (Andrews); "Fostering Excellence in Industrial Technology Faculty and Programs" (Bensen); "World Markets and…

This document is intended to help education and training institutions deliver the Machine Tool Advanced Skills Technology (MAST) curriculum to a variety of individuals and organizations. MAST consists of industry-specific skill standards and model curricula for 15 occupational specialty areas within the U.S. machine tool and metals-related…

This guide is intended to train teachers in integrating math skills into the vocational curriculum. Included in the guide are process outlines, handouts, and transparency masters for three workshops designed to assist in the development and delivery of an integrated vocational education and math skills program. The first workshop, a 3- to 4-hour…

This volume developed by the Machine Tool Advanced Skill Technology (MAST) program contains key administrative documents and provides additional sources for machine tool and precision manufacturing information and important points of contact in the industry. The document contains the following sections: a foreword; grant award letter; timeline for…