Volume II of the Education and Experience in Engineering E3 Program is a collection of 21 appendices related to this program which provide information on funding, participants, meetings, and communications among participants. Appendix V, an E3 Handbook for students, contains information on student advising, placement, and evaluation. Appendix VI…

This student module on the role of OSHA (Occupational Safety and Health Act) in Safety and Health is one of 50 modules concerned with job safety and health. This module looks at the OSHA Act, its aims, and the rights and responsibilities of employers and workers under the Act. Following the introduction, 16 objectives (each keyed to a page in the…

This student module on fire prevention and emergency procedures is one of 50 modules concerned with job safety and health. This module discusses the chemistry of fire and the methods for extinguishment, along with the steps necessary for emergency action. Following the introduction, 10 objectives (each keyed to a page in the text) the student is…

This student module on steel erection safety is one of 50 modules concerned with job safety and health. This module identifies typical jobsite hazards encountered by steel erectors, as well as providing safe job procedures for general and specific construction activities. Following the introduction, 11 objectives (each keyed to a page in the text)…

This student module on agricultural chemical and pesticide hazards is one of 50 modules concerned with job safety and health. This module contains information concerning the safe handling, use, and storage of many chemicals that are frequently used in the control of pests. Following the introduction, 10 objectives (each keyed to a page in the…

This second in a series of eight modules for a course titled Metrology dscribes fixed gages, dividers, calipers, vernier and dial calipers, and micrometers. The module follows a typical format that includes the following sections: (l) introduction, (2) module prerequisites, (3) objectives, (4) notes to instructor/student, (5) subject matter, (6)…

This third in a series of eight modules for a course titled Metrology describes gage blocks and mechanical and electronic comparators. The module follows a typical format that includes the following sections: (1) introduction, (2) module prerequisites, (3) objectives, (4) notes to instructor/student, (5) subject matter, (6) materials needed, (7)…

This sixth in a series of eight modules for a course titled Metrology describes the principles on which calibration programs are developed, no matter which instruments are included in the calibration program. The module follows a typical format that includes the following sections: (1) introduction, (2) module prerequisites, (3) objectives, (4)…

This eighth in a series of eight modules for a course titled Metrology describes the overall metrology program and the associated typical responsibilities of the quality assurance/quality control technician. The module follows a typical format that includes the following sections: (1) introduction, (2) module prerequisites, (3) objectives, (4)…

This tenth in a series of ten modules for a course titled Welding Inspection describes records associated with welding which serve three functions: specification of agreements, initiation of action in fulfillment of agreement, and historical evidence of action taken. The module follows a typical format that includes the following sections: (1)…

This second in a series of six modules for a course titled Civil/Structural Inspection describes the materials used in structural steel work; the standards according to which materials are purchased and inspected; fabrication, handling, and installation practices; and the various inspection tasks performed during erection operations. The module…

This sixth in a series of six modules for a course titled Civil/Structural Inspection describes inspection activities associated with pre-stressed concrete such as reviewing material certifications and test reports, inspecting construction operations, performing materials testing, and preparing records and reports of inspection and testing…

This fourth in a series of eight modules for a course titled Quality Assurance Practices describes the activities of identification, storage, and handling of components, parts, and materials. The module follows a typical format that includes the following sections: (1) introduction, (2) module prerequisites, (3) objectives, (4) notes to…

This eighth in a series of eight modules for a course titled Quality Assurance Practices describes the records management program for the collection, storage, and maintenance of records. The module follows a typical format that includes the following sections: (1) introduction, (2) module prerequisites, (3) objectives, (4) notes to…

This fourth in a series of six modules for a course titled Nondestructive Examination (NDE) Techniques II describes the specific technique variables and options which are available to the test technician, provides instructions for selecting and operating the appropriate test equipment, describes physical criteria for detectable discontinuities,…